Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
What're your beliefs about Tools You Need to Install a New Bathtub ?
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is readily obtainable, the job can move easily; if you have to open a wall surface to eliminate the old tub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. Make certain you have certified yourself for the work as well as fit attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is far better to think about using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will assist you install a brand-new bathtub in your shower room if you have currently bought a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools and also material checklist need to make up the following:
Planning for the Installation
To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using both wood boards under its feet, place the tub in the needed position. The wooden boards are helpful in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bath tub up until the spirit level reviews degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bath tub as well as also examine the overflow outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been used a minimum of once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washers remain in place between the tap and also the sink. Secure the faucet in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bath and the tiling, resulting in issues with wetness and feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can break fairly early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the market. It is advisable to fit the tiles making use of waterproof or water resistant sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that article about A Step-by-Step Guide to Installing a Bathtub through someone on our other website. Appreciated our blog posting? Please share it. Let others locate it. Thank you for your time. Please check up our site back soon.
Go Deal Now
Report this page